Full Power Mobile Phone Jammer Circuit Diagram

Full Power Mobile Phone Jammer Circuit Diagram.To day if we are talking about expert Cell phone Jammers we are conversing about this schematic underneath. First off all you should be very very cautious how to use this apparatus. Its completely illegal and so the reason. I post this Circuit is only for educational and testing causes. This type of apparatus is being utilised by security for VIPS, particularly at their limousines to avoid blasting device initiating while the vehicle passes from the goal cell phone-bomb. Off course there are those who use it to make a antic or to make the persons crazy in the rectangle block you are. 

The power of the jammer is currently sufficient to do your thing, but certainly you can place a 30W linear power amp at the RF output and impede a much wider locality. So, Be pleasant individual with that and recall that there are people who may need desperately to obtain or make a call and one of them could be you! And if you can't oppose of functioning the jammer do it for couple of secs. Do not forget that if you connect linear amp the unit will be a current sucker after all. 

Full Power Mobile Phone Jammer Circuit Diagram

Full Power Mobile Phone Jammer Circuit Diagram

Full Power Mobile Phone Jammer Circuit Diagram

Full Power Mobile Phone Jammer Circuit Diagram

Full Power Mobile Phone Jammer Circuit Diagram


Main Components of Jammer:
The Jammer output focus around PF0030 MOSFET amplifier by Hitachi, which offers high stability of VSWR = 20 : 1 and low power control current of 400 mA. Few things about PF0030: · Unevenness and distortion at the surface of the heat sink attached module should be less than 0.05 mm. · It should not be existed any dust between module and heat sink. · MODULE should be separated from PCB less than 1.5 mm. ·

Soldering temperature and soldering time should be less than 230°C, 10 sec. (Soldering position spaced from the root point of the lead frame: 2 mm) · Recommendation of thermal joint compounds is TYPE G746. (Manufacturer: Shin-Etsu Chemical, Co., Ltd.) · To protect devices from electro-static damage, soldering iron, measuring-equipment and human body etc. should be grounded. · Torque for screw up the heatsink flange should be 4 to 6 kg · cm with M3 screw bolts. · Don’t solder the flange directly. · It should make the lead frame as straight as possible. ·

The module should be screwed up before lead soldering. · It should not be given mechanical and thermal stress to lead and flange of the module. · When the external parts (Isolator, Duplexer, etc.) of the module are changed, the electrical characteristics should be evaluated enough. · Don’t washing the module except lead pins. ·

To get good stability, ground impedance between the module GND flange and PCB GND pattern should be designed as low as possible. Next comes the MAX2622 a self-contained voltage- controlled oscillators (VCOs) combine an integrated oscillator and output buffer in a miniature 8-pin ?MAX package. The inductor and varactor elements of the tank circuits are integrated on-chip, greatly simplifying application of the part. In addition, the center frequency of oscillation and frequency span are factory preset to provide a guaranteed frequency range versus control voltage. An external tuning voltage controls the oscillation frequency. The output signals are buffered by an amplifier stage matched on-chip to 50?.

The MAX2622 VCO is implemented as an LC oscillator topology, integrating all of the tank components on-chip. This fully monolithic approach provides an extremely easy-to-use VCO, equivalent to a VCO module. The frequency is controlled by a voltage applied to the TUNE pin, which is internally connected to the varactor. The VCO core uses a differential topology to provide a stable frequency versus supply voltage and improve the immunity to load variations. In addition, there is a buffer amplifier following the oscillator core to provide added isolation from load variations and to boost the output power. Output Buffer: The oscillator signal from the core drives an output buffer amplifier.

The amplifier is constructed as a common-emitter stage with an integrated on-chip reactive output match. No external DC blocking capacitor is required, eliminating the need for any external components. The output amplifier has its own VCC and GND pins to minimize load-pulling effects. The amplifier boosts the oscillator signal to a level suitable for driving most RF mixers. Tune Input: The tuning input is typically connected to the output of the PLL loop filter. The loop filter is presumed to provide an appropriately low-impedance source.

It may incorporate an extra RC filter stage to reduce high-frequency noise and spurious signals. Any excess noise on the tuning input is directly translated into FM noise, which can degrade the phase-noise performance of the oscillator. Therefore, it is important to minimize the noise introduced on the tuning input. A simple RC filter with low corner frequency is needed during testing in order to filter the noise present on the voltage source driving the tuning line. Layout Issues:

Always use controlled impedance lines (microstrip, coplanar waveguide, etc.) for high-frequency signals. Always place decoupling capacitors as close to the VCC pins as possible; for long VCC lines, it may be necessary to add additional decoupling capacitors located further from the device. Always provide a low-inductance path to ground, and keep GND vias as close to the device as possible. Thermal reliefs on GND pads are not recommended. Circuit Description: The circuit emits a carrier that sweeps across the cellular band.

The Regulator S-80830ALY is made by SEIKO and is a 3V high precision device and you can use any other similar regulator. The 78L05 on the other hand provide with 5 volts the ~1KHz sweeper circuit (which consist from the NPN transistor 2N4401 and the LM741) and the MAX2622 who does the oscillation to the desired frequency. TR1 is the main frequency adjuster and TR3 adjust the signal for best spectrum damage and should be set to slightly less than 1 Volt peak to peak. TR2 is for tunning the output of approximately 880 MHz (~1.2V). You can use any 12V power supply and 1A should be enough. Finally TR4 adjusts the RF power output to 200-300 mW. Do not forget to ground the PF0030 MOSFET amplifier and put a nice heatsink as well.

Coaxial cable RG58 or any other type 50hom cable should be used between the pin7 of MAX2622 and pin1 of Hitachi PF0030 (RF to that point should be +13dBm MAX) and offcourse coaxial at the output to the antenna. Coils L1, L2 and L3 are Ferrite Beads. For antenna, if you want best results, you need a high gain omnidirectional antenna. Can also be used to jam 800 MHz radios as well as SMR radios and may do damage to ISM 900 MHz band. The third harmonic of a sweeping 800 - 828 MHz signal will jam devices operating in the 2.4 GHz ISM band. Anyway by careful with that little monster.


Sourced by: maxim

0 comments:

Post a Comment

All updates in Your Inbox

Enter your email address:

Delivered by FeedBurner

 

Copyright @ 2013 Electronic Circuit Diagrams & Schematics.

Designed by AS & AS